Miter bend calculator: cut angles, piece lengths and a 16-point template
For a miter bend, each cut is at total angle ÷ (2 × (pieces − 1)) from square. A 3-piece 90° miter has two cuts at 22.50°; on 6" pipe with a 9" centreline radius the end pieces are 3-3/4" and the middle piece 7-7/16" on the centreline. FitterMaster's Miter screen gives those and the 16 cutbacks to lay out.
When does a miter bend make sense?
A segmented (miter) elbow is built from straight pipe when no fitting is available, on large diameters, or when the bend radius must be bigger than a standard ell. The more pieces, the smoother the bend and the smaller each cut angle. Laying one out by hand can take a few tries to get the stations right; the app skips straight to the numbers.
What is the miter bend formula?
- Cut angle α = total angle ÷ (2 × (pieces − 1)).
- Number of cuts = pieces − 1.
- End piece length (centreline) = Rc × tan α; middle piece = 2 × Rc × tan α, where Rc is the centreline radius.
- Ordinate at each station = (OD ÷ 2) × tan α × cos φ, at 16 stations 22.5° apart. The cutback is the longest ordinate minus each one.
How do you lay out a miter bend in FitterMaster?
- Open Miter under Calculate (Pro).
- Under Pipe, pick the Size. The OD comes from the pipe table.
- Under Bend, set Total Angle (15° to 135°), the number of pieces with the pieces stepper (2 to 8) and type your Centreline Radius. It starts at 9".
- Read Cut Angle (each) and Number of Cuts under Miter Cuts, plus the end and middle piece lengths in the note.
- Use the Wrap Template: 16 stations around the pipe, marked back from station 1, the longest.
Worked example: 3-piece 90° on 6" pipe
6" pipe (OD 6.625"), Total Angle 90°, 3 pieces, Centreline Radius 9": Cut Angle (each) 22.50°, Number of Cuts 2, end pieces 3-3/4", middle piece 7-7/16".
| Station | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |
|---|---|---|---|---|---|---|---|---|---|
| Cutback | 0" | 1/8" | 3/8" | 7/8" | 1-3/8" | 1-7/8" | 2-5/16" | 2-5/8" | 2-3/4" |
Stations 10 to 16 mirror 8 back down to 2: 2-5/8", 2-5/16", 1-7/8", 1-3/8", 7/8", 3/8", 1/8". Station 9 is the short side, directly opposite station 1.
More pieces, smaller cuts
| Pieces | Cut Angle (each) | Cuts | End piece | Middle piece | Largest cutback |
|---|---|---|---|---|---|
| 3 | 22.50° | 2 | 3-3/4" | 7-7/16" | 2-3/4" |
| 4 | 15.00° | 3 | 2-7/16" | 4-13/16" | 1-3/4" |
| 5 | 11.25° | 4 | 1-13/16" | 3-9/16" | 1-5/16" |
Transferring the template to the pipe
- Divide the circumference into 16 equal parts with a wrap-around and number them from the longest point.
- Draw a square reference line round the pipe, measure each cutback back from it, and join the points with a smooth curve.
- Nothing is printed: the numbers are on screen, and you lay them out yourself.
- The centreline radius is your choice. The app does not derive it from the pipe size, so type the one on your drawing.