Pipe weight calculator for steel pipe, empty and full of water
Pick the NPS, the schedule and the length: the calculator returns the weight of the empty pipe and of the water-filled pipe, per foot or meter and in total. 4" Sch 40 is 10.79 lb/ft empty and 16.31 lb/ft full. FitterMaster's Pipe Data gives the empty weight offline on site.
How much does a length of pipe weigh, empty and full?
Rigging a spool, sizing a hanger or checking a hydrotest load all need the same two numbers: the steel and the water inside it. The steel depends on the NPS and the schedule; the water depends only on the inside diameter. Enter both below and switch to metric if your drawings are in meters and kilograms.
Pipe weight calculator: empty and filled with water
- Distance between bends
- Shrink
- Multiplier
Enter numbers of zero or more; the set or the roll must be above zero.
Showing the worked example. Turn on JavaScript to calculate your own numbers.
Carbon steel: weight = (OD − wall) × wall × 10.6802 lb/ft (ASME B36.10M nominal dimensions), water at 62.4 lb/ft³ (1,000 kg/m³). Nominal wall only: no mill tolerance (up to −12.5 %), coating, insulation, fittings or flanges. Check the project spec for hydrotest and support loads.
What are the formulas for steel and water weight?
- Steel (lb/ft) = (OD − wall) × wall × 10.6802, with OD and wall in inches. Multiply by 1.48816 for kg/m.
- Water (lb/ft) = π ÷ 4 × ID² × 62.4 ÷ 144, which is about 0.34 × ID² with ID in inches. In metric, 1 liter of water weighs 1 kg, so kg/m = liters per meter.
- ID = OD − 2 × wall. The OD is set by the NPS; a heavier schedule only thickens the wall and shrinks the ID, so it adds steel and removes water.
Schedule 40 pipe weight with water: examples
| NPS | ID | Empty lb/ft | Water lb/ft | Full lb/ft | Empty kg/m | Full kg/m |
|---|---|---|---|---|---|---|
| 2" | 2.067" | 3.65 | 1.45 | 5.11 | 5.44 | 7.60 |
| 4" | 4.026" | 10.79 | 5.52 | 16.31 | 16.06 | 24.27 |
| 6" | 6.065" | 18.97 | 12.52 | 31.50 | 28.24 | 46.88 |
| 8" | 7.981" | 28.55 | 21.69 | 50.24 | 42.49 | 74.77 |
Worked example: 20 ft of 4" Sch 40 weighs 20 × 10.79 = 215.8 lb empty, and 20 × 16.31 = 326.2 lb full of water. The water is a third more than you might expect, and on 8" and larger the water outweighs the steel.
How do you look up the empty weight in FitterMaster?
- Open Pipe Data under Reference.
- Pick the Schedule. STD and Sch 40 are free; Sch 10, XS, Sch 80, Sch 160 and XXS need the upgrade.
- Read OD, ID and lb/ft for your NPS. Sizes not made in that schedule are left out.
- Add the water from this page if the line will be full.
What does this calculator leave out?
- Carbon steel to ASME B36.10M only. Stainless (B36.19), copper, PVC and other standards weigh differently.
- Nominal wall: mills may roll pipe up to 12.5 % under, so a real joint can weigh a little less.
- Water at 62.4 lb/ft³ (1,000 kg/m³). Oil, brine or steam condensate need their own density.
- No coating, insulation, valves, flanges or fittings, and no pressure rating.
Questions and answers
How much does 4 inch Sch 40 pipe weigh per foot with water?
How do I calculate the weight of a pipe full of water?
Does FitterMaster add the water weight?
Does the calculator work in kilograms and meters?
You might also like
- How to determine the weight of a load before lifting it · RigMaster
- Carbon equivalent formula and preheat temperature for welding A36, 4140 and carbon steel · WeldMaster