Pipe saddle template calculator: fish mouth and 45 degree lateral layout
A saddle template is 16 cutbacks around the branch pipe, worked out from the real ODs of branch and header. A 4" branch on a 6" header at 90° has a deepest cutback of 7/8"; at 45° as a lateral the deepest is 4-1/2". FitterMaster's Saddle & Lateral screen calculates both.
What is a saddle, fish mouth or lateral cut?
When a branch sits on the outside of a header, the end of the branch has to be cut to the curve of the header. At 90° that cut is a saddle, or fish mouth. At a shallower angle it becomes a lateral, with a long heel on one side and a short throat on the other. Grinding a fish mouth to a tight fit beats freehanding it from eye — 16 stations beats guessing every time.
How are the saddle ordinates worked out?
- R = header OD ÷ 2, r = branch OD ÷ 2, φ = the station angle round the branch.
- Saddle (90°): reach x(φ) = √(R² − r² cos² φ).
- Lateral at angle β: t(φ) = [√(R² − r² cos² φ) − r sin φ cos β] ÷ sin β.
- Cutback = longest reach − each reach, at 16 stations. Station 1 is always the longest.
How do you get the template in FitterMaster?
- Open Saddle & Lateral under Templates (Pro).
- Under Pipes, pick the Header (run) size and the Branch size.
- Under Fit, set Branch Angle β: 90° for a saddle, 30° to 89° for a lateral.
- Read the Wrap Template: 16 numbered cutbacks and a profile drawing of the cut.
- If you see Branch must be ≤ header OD., the branch is larger than the header; swap the sizes.
Example: 4" branch on a 6" header at 90°
| Station | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|---|---|---|---|---|---|---|---|---|
| Cutback | 0" | 1/8" | 7/16" | 3/4" | 7/8" | 3/4" | 7/16" | 1/8" |
Stations 9 to 16 repeat the same pattern: a saddle has two high points and two low points. The deepest cutback, at stations 5 and 13, is 7/8" (0.8814").
Size on size, 4" on 4", the deepest cutback grows to 2-1/4" at stations 5 and 13, because the branch wraps right round the header.
Example: 45° lateral, same pipes
| Station | Cutback | Station | Cutback |
|---|---|---|---|
| 1 | 0" | 9 | 4-1/2" |
| 2 | 5/16" | 10 | 4-1/2" |
| 3 | 1-1/4" | 11 | 4-7/16" |
| 4 | 2-7/16" | 12 | 4-1/8" |
| 5 | 3-1/2" | 13 | 3-1/2" |
| 6 | 4-1/8" | 14 | 2-7/16" |
| 7 | 4-7/16" | 15 | 1-1/4" |
| 8 | 4-1/2" | 16 | 5/16" |
Station 1 is the heel, the long point; the stations around 9 form the throat.
Laying it out on the branch
- Wrap a strip round the branch and divide it into 16 equal spaces, numbering from station 1.
- Scribe a square line round the pipe, then mark each cutback back from that line and join the points.
- Cut and bevel to your procedure. The app gives the fit-up line, not a bevel angle.
- It covers saddle-on branches only: no set-in (saddle-in) cut, no hole template for the header and no off-center branches.