Welding symbols chart explained: arrow side, other side and the numbers
A symbol below the reference line is welded on the arrow side of the joint; above the line it is the other side. Put 1/4 to the left of a fillet triangle and 2–6 to the right and you have a 1/4" fillet, 2" long, every 6" centre to centre. WeldMaster's free Weld Symbols reference draws every symbol and lets you flip the side.
How do you read a welding symbol?
A welding symbol is built on a horizontal reference line. Everything about the weld hangs off that line, and the position of each item tells you what it means.
- Reference line: the horizontal line that carries the symbols and numbers.
- Arrow: leaves one end of the line and touches the joint. It defines the arrow side.
- Tail: an optional fork at the other end that carries notes such as the WPS or process.
- Weld symbol: the small drawing on the line that shows the type of weld.
- Supplementary marks at the bend: a circle for weld all around, a flag for a field weld.
Arrow side vs other side: which side is the weld on?
In AWS A2.4 the arrow side is always drawn below the reference line, and the other side above it. A symbol below the line means the weld is on the same side of the joint that the arrow touches. A symbol above the line means the opposite face. Symbols on both sides mean a weld on each side. Spot and seam symbols are centred on the line, so resistance welds have no arrow or other side.
Bevel, J-groove and flare-bevel symbols have a vertical leg that is always on the left, and the arrow bends toward the piece that gets the preparation.
What do the basic weld symbols mean?
| Symbol | What it describes | Shape on the line |
|---|---|---|
| Fillet | Triangle weld at a T, lap or corner joint | Right triangle, vertical leg on the left |
| Square groove | Butt joint with a root gap and no bevel | Two parallel vertical lines |
| V-groove | Both edges bevelled to form a V | A V with its point on the line |
| Bevel groove | One edge bevelled | Vertical leg plus a slanted line |
| U-groove | Both edges machined to a rounded U | A U touching the line |
| J-groove | One edge machined to a J | Vertical leg plus a curved line |
| Plug / slot | Weld fills a hole or slot | Open rectangle on the line |
| Spot | Round spot weld | Circle on the line |
| Seam | Continuous overlapping spots or roller weld | Circle crossed by two lines |
| Back / backing | Weld or strip on the root side | Half circle opposite the groove |
Where do the numbers go on a welding symbol?
- Size goes to the left of the symbol: fillet leg length, or groove depth.
- Length and pitch go to the right: 2–6 means welds 2" long, 6" apart centre to centre.
- Groove angle and root opening are written with the groove symbol.
- Contour marks (flush, convex, concave) sit on the outer side of the symbol, with a letter such as G for grinding or M for machining.
How do AWS and ISO symbols differ?
AWS puts the arrow-side symbol below the reference line. ISO 2553 adds a dashed identification line next to a solid one: a symbol on the solid-line side is the arrow side and one on the dashed-line side is the other side, and the dashed line can be left out for symmetrical welds. AWS size for a fillet is the leg length; ISO gives the throat thickness (a5) or the leg length (z7). AWS writes length-pitch as 2–6; ISO writes number × length (gap), such as 3×50 (100).
How do you decode a symbol in WeldMaster?
- Open Weld Symbols from Reference on the main screen. It is free.
- Tap Read a weld symbol.
- Under Decoder, pick the Symbol and switch Weld all around or Field weld on if the drawing shows them.
- Flip between Arrow side, Other side and Both sides and watch the symbol move above or below the line.
- Go back and open any entry under Basic symbols or Supplementary symbols for its meaning.
Questions and answers
Is the arrow side always below the line?
What does the circle at the bend of a welding symbol mean?
What does 1/4 and 2–6 mean on a fillet symbol?
You might also like
- MIG porosity, spatter and burn-through: causes and how to fix them · WeldMaster
- How to calculate heat input in welding, in kJ/in and kJ/mm · WeldMaster
- Fillet weld symbol: what the size and length numbers mean · WeldMaster
- Groove weld symbols: V, bevel, U and J · WeldMaster
- Weld all around, field weld and finish symbols · WeldMaster
More WeldMaster guides
- MIG welding settings chart: voltage, wire speed and gas by metal thickness
- Flux core welding settings and polarity: gasless vs dual shield
- Stick welding amperage chart for 6010, 6011, 6013, 7014, 7018 and 7024 rods
- Carbon equivalent formula and preheat temperature for welding A36, 4140 and carbon steel
- MIG porosity, spatter and burn-through: causes and how to fix them
- All questions about WeldMaster
- Back to WeldMaster